imm in a hurry will ifx this as soon as i get home:


this is not mine.... if i write this, its gonna be too long

************************************************** ******
The Ultimate Tutorial For Installing iXtreme 1.6
For All DVD Drives!
By
yhbtimblk & Stevoal
************************************************** ******

iXtreme 1.6 is the new DVD Drive firmware that allows your Xbox 360 to play backups - Including the new backups with 3 video partitions.
It will also allow you to rip games using your Xbox 360 DVD drive connected to your computer.

With iXtreme firmware you play both original and backup games with no hardware modification.

This Tutorial will show you in detail how to install iXtreme firmware on your Xbox 360 DVD drive.

Requirements

- A desktop computer with a free PCI slot on the motherboard.
- A USB Flash Drive.
- A VIA 6421A PCI card.

First thing you need to do is check which DVD drive your Xbox 360 has.
There is 4 different types of Xbox 360 DVD Drives - But don't worry they can all be modified.

Remove the Xbox 360 faceplate and look into hole #3 on the diagram shown below.

[Only Registered Users Can See LinksClick Here To Register]

[Only Registered Users Can See LinksClick Here To Register] white wire means that the DVD drive inside your Xbox 360 is BenQ.

[Only Registered Users Can See LinksClick Here To Register] red wire means that the DVD drive inside your Xbox 360 is Samsung.

[Only Registered Users Can See LinksClick Here To Register] covering the hole means that the DVD drive inside your Xbox 360 is Hitachi.

[Only Registered Users Can See LinksClick Here To Register] yellow wire means that the DVD drive inside your Xbox 360 is LiteOn.


Ok now you will have to open your xbox 360.
Watch this video - It will show you how to open up your Xbox 360 without voiding the warrenty

[Only Registered Users Can See LinksClick Here To Register]
************************************************** ******
Tutorial
For
BenQ and Samsung
Drives
************************************************** ******

You can download all the files that you will need from here:

[Only Registered Users Can See LinksClick Here To Register]
Password - [Only Registered Users Can See LinksClick Here To Register]

1.) Make sure that your VIA 6421A PCI Card is installed in your computer motherboard.

2.) Install the latest VIA 6421A Sata Drivers.
Run "Setup.exe" in the "VIA 6421A V580C Driver" folder from the .rar file you downloaded earlier.
Once the drivers are installed you will have to restart your computer.

[Only Registered Users Can See LinksClick Here To Register]


3.) Open the "iPrep 101" folder from the .rar file you previously downloaded.
Open "iPrep.exe". iPrep will automatically load ixtreme 1.6 firmware for both BenQ and Samsung DVD Drives.

Select your USB pen drive.
Make sure the boxes "Format/Make Bootable" and "Include Batch Files" are both ticked.
Then click "Start".

[Only Registered Users Can See LinksClick Here To Register]

[Only Registered Users Can See LinksClick Here To Register]

4.) Turn off both the x360 and the computer.
Now you have to connect your Xbox 360's DVD Drive to your computer.
Plug the sata cable into your VIA 6421A PCI card and plug the other end into your x360 DVD Drive. You will have to unplug the left cable on the DVD Drive to do so.

[Only Registered Users Can See LinksClick Here To Register]

Now make sure that you have plugged the sata cable into the correct port on the VIA 6421 PCI Card:

[Only Registered Users Can See LinksClick Here To Register]

5.) Go into your computers Boot settings and set your USB pen drive as
the default boot device.

[Only Registered Users Can See LinksClick Here To Register]

Make sure both the Xbox 360 and computer are turned off.
Unplug all devices connected to your computer.
e.g Hard Drive, DVD Drive etc

Plug in your USB drive into your computer and turn it on.
The computer should now boot up into a black DOS screen like this.

[Only Registered Users Can See LinksClick Here To Register]

6.) Now make sure that the Xbox 360 is off but both the power cable and
AV cable are connected.
Now type "dosflash".
Now turn on your Xbox 360 by using your faceplate and then press enter on the keyboard.

If you are asked if you want to send magic keys type "N" and press enter on your keyboard.

If you are asked about sending the magic keys it will then give you instructions and ask you if you are ready - Ignore the instructions, type "N" on the keyboard and press enter.

Dosflash will automatically detect your Xbox 360 and a message will say:

MTK Vendor Intro failed on port:
If you choose to rend the command you should turn the drive off and on after you have pressed "Yes".
Do you want to resend the command until the drive responds (Y/N)?

Type "Y" and press enter.

A message will say.
Status: 0x51

Turn off the drive and wait 10 seconds.

A message will say.
Status: 0xD1

Now turn the Xbox 360 back on by using your Xbox 360 faceplate.

Now a list of devices will be listed, select the port of your xbox 360 DVD Drive and press enter.

Now you will be asked what you want to do to the drive. [R] read, [W] write or [E] erase.
Type "r" and press enter.

Then it will as you where you want to save the original firmware.
Type "c:\orig.bin" and press enter.

It will now start to read the original firmware.

Reading Bank 0...OK!
Reading Bank 1...OK!
Reading Bank 2...OK!
Reading Bank 3...OK!
Reading finished!

You can now turn off both the Xbox 360 and the computer.

7.) Plug your hard drive back into your motherboard and boot into windows.
Now run "360FwTb.exe" from the "X360 Firmware Toolbox 48" folder.

Select "File" then "Open".

[Only Registered Users Can See LinksClick Here To Register]

Now browse to the "orig.bin" on your USB pen drive and select "Open".

[Only Registered Users Can See LinksClick Here To Register]

It will now show you your drive key highlighted. Right click on the drive key and select "Copy".

[Only Registered Users Can See LinksClick Here To Register]

Now open the "ix16.bin" from the "iXtreme 1.6 Firmware" folder and then either the "BenQ" or "Samsung" folder depending on your dvd drive. All from the .rar file you downloaded earlier.

The drive key will show as 777777777777777777.
Right click on the drive key and select "Paste".

[Only Registered Users Can See LinksClick Here To Register]

Now click "Save Key".
A message will say "A new key has been set".

[Only Registered Users Can See LinksClick Here To Register]

You can now close the program.

8.) Now your DVD Drive Key is copied and the Drive firmware is now modified to play backups.
Place the "ix16.bin" you just created onto the root of your USB Pen Drive.

9.) Make sure both the Xbox 360 and computer are turned off.
Once again remove any devices from the computer and boot from the USB Drive.

Now make sure that the Xbox 360 is off but both the power cable and
AV cable are connected.
Now type "dosflash".
Now turn on your Xbox 360 by using your faceplate and then press enter on the keyboard.
It will automatically detect your Xbox 360 and a message will say:

MTK Vendor Intro failed on port:
If you choose to rend the command you should turn the drive off and on after you have pressed "Yes".
Do you want to resend the command until the drive responds (Y/N)?

Type "Y" and press enter.

A message will say.
Status: 0x51

Turn off the drive and wait 10 seconds.

A message will say.
Status: 0xD1

Now turn the Xbox 360 back on by using your Xbox 360 faceplate.

Now a list of devices will be listed, select the port of your xbox 360 DVD Drive and press enter.

Now you will be asked what you want to do to the drive. [R] read, [W] write or [E] erase.
Type "w" and press enter.

Then it will as you what firmware you want to write to the drive.
Type "c:\ix16.bin" and press enter.

It will now start to write the Ixtreme 1.6 firmware.

Erasing...OK!
Erasing finished!
Writing Bank 0...OK!
Writing Bank 1...OK!
Writing Bank 2...OK!
Writing Bank 3...OK!
Writing finished!

And now your Xbox 360 is flashed with iXtreme 1.6!
Just turn your Xbox 360 and computer off, put the Xbox 360 back together again.

Make sure you make a backup of the "orig.bin" that is on your USB Drive!

Enjoy iXtreme 1.6

************************************************** ******
Tutorial
For
Hitachi
Drives
************************************************** ******

This tutorial is for iXtreme 1.51 because iXtreme 1.6 has not yet been released for Hitachi drives.
Once the firmaware is released the tutorial will be updated.
iXtreme 1.51 still plays backups with the 3rd wave video partition

You can download all the files that you will need from here:

Hitachi files on rapidshare.


Firstly you will have to open your xbox 360. If you are unsure how to please search on youtube lots of vids for it.



***VIA users with no drivers, must either install drivers, or, utilise PortIO –you will not be
assigned a drive letter in windows with no drivers!!!***

***Windows API Users, after setting ModeB, you must wait for hardware changes to be
detected (15 secs) If nothing is detected, click “Refresh***

Please note if your Hitachi DVD drive is already flashed you will need to restore the original firmware before flashing new firmware. Please see below.


Setting Mode-B

Hitachi drives need to be in Mode B to be able to read and write to the drive. So first of all we need hook up the Hitachi drive to your PC via sata. If you have a CK3 or Maximus then all the better, if not you will need to use the 360 to power the drive when connected via sata. So you will need ur power pack and AV cable plugged into the back of the 360.

Ok now turn on the drive. (Blue light to be lit if using CK3).
Open Jungleflasher in the pack you downloaded earlier and click on Hitachi at top.

[Only Registered Users Can See LinksClick Here To Register]


Make sure you have the correct port selected. You can find your port number opening up Iprep 8 and selecting ur Via chipset and looking for the 4 digits below ur selected chipset.

[Only Registered Users Can See LinksClick Here To Register]

[Only Registered Users Can See LinksClick Here To Register]

Once you have the correct port make sure that you select either Win API or PortIO depending on ur setup. Win API seems to work best for XP with VIA 6421a chipset. And also select which drive you are flashing. Make sure if your using Win API that you leave the system for 15secs or so to check for hardware changes after pushing "send mode b". Basically it looks for your drive. Ok so make sure


1. You have the correct port selected.

2. Choose whether to use Win API or PortIO

3. Select Drive and transfer method. (Use Classic for all drives apart from 78/79. If 78/79 use RAM Upload)

4. In flashing options make sure Dump Drive is selected

5. Then click "Send Mode-B"


You should see this
[Only Registered Users Can See LinksClick Here To Register]

Follow the instructions push ok


You should then see this.

[Only Registered Users Can See LinksClick Here To Register]


**79 drive only**, you will now need to unlock the drive. Go to the folder you have downloaded and install Image Burn if you have not already. Once installed go into the 79unlock cd folder and right click on the .cue file and burn with image burn on a blank cd-r.**
[Only Registered Users Can See LinksClick Here To Register]

Once burned you now eject the DVD drive and insert the burned disk into the Hitachi v79 drive and close down any auto runs, and then click on the 79 Unlock button.
[Only Registered Users Can See LinksClick Here To Register]

You should see this

[Only Registered Users Can See LinksClick Here To Register]

Your drive is now unlocked and ready to dump the firmware.



Firmware Dumping


**Please note if you have a 78/79 drive you must use RAM Upload in transfer method.**


Now ur in Mode-B just double check ur settings you have made in the previous steps. if all ok then Click "Read to Source"
[Only Registered Users Can See LinksClick Here To Register]

This will now dump the drive

[Only Registered Users Can See LinksClick Here To Register]


Once the Original firmware is dumped it will prompt you to save it.

[Only Registered Users Can See LinksClick Here To Register]


Save it and make sure you put it somewhere safe I ususally put them in a folder with the console serial number then you dont forget.


Once saved it should open in Firmware Tool.

[Only Registered Users Can See LinksClick Here To Register]


Make sure you check the Firmware Type, if Stock then your good to flash, if not dont worry As when you try to flash the ixtreme 1.51 firmware it will throw a popup and show this

[Only Registered Users Can See LinksClick Here To Register]


If you have stock firmware then skip this part to the flashing section.


Restoring Original Firmware


Ok if you have modded firmware already on your drive you will need to restore to the original here.


Simply make sure all your settings are correct for your Hitachi drive, and click on "Restore Firmware" in flashing options and click "restore to stock" button.

[Only Registered Users Can See LinksClick Here To Register]

It will now do a stability test on your drive

[Only Registered Users Can See LinksClick Here To Register]

It should show stable in the prompt message if ok just push "Yes"


It will now check the checksum and fix. Just push "Ok". Make sure you check the log and that it all looks good like below.

[Only Registered Users Can See LinksClick Here To Register]



Flashing Ixtreme 1.51

Simply again just make sure all your settings are correct for your drive and select "Flash Ixtreme" in Flashing Options. Then click "Flash Hacked f/w" button.

[Only Registered Users Can See LinksClick Here To Register]

It will again prompt you to save the firmware you are reccomended to do so.


It will then do another stability test. If reports stable just push "Yes" to continue.


Jungleflasher will then start flashing the sectors.


Once it has finished check the log and you should see this.

[Only Registered Users Can See LinksClick Here To Register]

Well done you have just flashed your Hitachi.


Stevoal

************************************************** ******
Tutorial
For
LiteOn
Drives
************************************************** ******

What you need:

Key extractor like the CK3+probe or the Maximus
Download this file to use with this tut.
Code:

[Only Registered Users Can See LinksClick Here To Register]


Install Portio32 if not already. No need to uninstall any via drivers.
VIA 6421a chipset



Tutorial

1. If this is the first time flashing a Liteon you need to unscrew the 4 screws on the bottom of the drive and take off the bottom plate.

[Only Registered Users Can See LinksClick Here To Register]


2. Hook up ur Liteon via Sata to ur PC, be sure to be careful and make sure you connect the cables properly into the back, because if you are using the CK3 and plug in the wrong way you will blow it. The small cable from the CK3 has 2 tabs on them to show which correct way to put in, because the drive is upside down make sure they are facing the top of the drive. If you don?t know what I mean then google it.

3. Power on the drive using the CK3 or Maximus. Open the drive tray, turn off the CK3 or Maximus and the push the tray half way back in manually. Then turn the drive back on again.
[Only Registered Users Can See LinksClick Here To Register]

4. Open up Jungleflasher in the folder you downloaded earlier and go to DVDKey 32 tab. Make sure the correct I/O port is selected and shows ur Liteon drive as below. Also make sure you have the correct COM port selected for the key grabber usually COM 3
[Only Registered Users Can See LinksClick Here To Register]
[Only Registered Users Can See LinksClick Here To Register]
**If you have the new 83850 firmware Liteon then see the PDF file in the folder you downloaded everything is in there.** If not then carry on.

5. You now need to get ur probe or spear and put it on the R707 point as show here.
[Only Registered Users Can See LinksClick Here To Register]

It should show a green light if all is good.

6. Click Get Key while holding the spear or probe on the R707 point.
[Only Registered Users Can See LinksClick Here To Register]

It will dump the key 4 or 5 times and then load up a save as prompt, this is ur dummy.bin file which is very important to keep safe and put somewhere safe. Save it and then it will ask you if you want to auto load 1.6 say yes.

7. Click spoof source to target and then click Save to File next to the target firmware. Save that in the same folder you saved your dummy.bin, this should be Lite_CFW.bin, that is the custom firmware your about to flash to ur drive. (Make sure you have both files saved somewhere)

8. Click on MTK Flash 32 tab and click on Lite-On Erase say yes and follow the instructions on screen.

[Only Registered Users Can See LinksClick Here To Register]
[Only Registered Users Can See LinksClick Here To Register]
[Only Registered Users Can See LinksClick Here To Register]

The Liteon is now erased and ready for your new firmware.

9. Simply click Write in flashing tasks and let it verify the write and ur done.


Notes:
If your computer freezes when you erase the drive in Jungleflasher you have semi-bricked ur drive, but not to worry. You will need a bootable USB and put these files on it. Boot up from the USB into DOS and follow these instructions. (Make sure you know what port ur drive is located on. i.e. B800. Its the I/O port on DVDkey 32 or MTK Flash 32 tabs you want the last 4 digits.)
1. Put all the files from this download onto the root of the USB not the folder just the progs inside it.
Code:

[Only Registered Users Can See LinksClick Here To Register]


2. Put the Lite_CFW.bin file onto the root of the USB as well
3. Boot up into DOS from the USB with the drive turned on.
4. Type l-o-eras.exe B800 (B800 being ur port number) push enter
5. Type l-o-eras.exe b800 again and push enter.
6. Turn off the CK3 or Maximus and turn on again
7. Type l-o-eras.exe b800 again and enter
8. type l-o-eras.exe b800 once more and enter
9. You should now have a status 072.
10. Turn off the drive and on once more.
11. Type dosflash push enter
12. check to see which drive number ur drive is on. Should be 0. Say no to any on screen messages until u get to the bit where it asks you for a driver number type it in and push enter.
13. Type W and hit enter.
14. type Lite_CFW.bin and hit enter let it write and ur done.

Thanks... Stevoal

F.A.Q


How do i rip games using the new iXtreme firmare?

Eject the drive tray but hold it half way open and turn off the power. Once booted into windows power on the DVD drive while still holding the drive try half way open. After about 5-10 seconds the DVD drive will be detected as new hardware in windows. Now just use Xbox Backup Creator the rip the game

My DVD drive already has an older version of iXtreme installed - How do i upgrade?

The same way as if the drive had stock firmware - Read the drive firmware, copy the key into the iXtreme firmware, write the firmware to the drive.

All done, but once i insert a game i get "Play DVD". Wtf.

Either the Xbox 360 SATA cable is not plugged back into the DVD drive or the Drive key in the iXtreme is not correct. Use Maximus Firmware Toolbox to check that the drive key matches the one from your orig.bin.

Can i just use my motherboard SATA instead of buying a VIA 6421A PCI card?

Your motherboard SATA might work fine, only way to know is to try it.
You will probably need to buy the VIA PCI card.

Can i get banned from xbox live for playing backups?
Yes. There is always a slight chance.
If you check your games with ABGX360 then the risk of getting banned is very slim -

My computer does not have SATA, can't i just use a USB to SATA adapter?